400MPa级超细晶粒钢焊接接头的低温韧性

利用CO2+Ar气体保护焊,分别采用单道焊接和双道焊接工艺对厚度为8 mm的400 MPa级超细晶粒钢钢板进行了焊接,采用系列冲击试验方法对焊接接头的低温韧性进行了研究。试验结果表明,在焊接接头中,焊逢位置低温韧性较差。由于双道焊较小的热输入,减小了焊缝及热影响区组织粗化,其焊接接头的低温韧性好于单道焊,并使热影响区面积变小。     

气流循环粉碎法制备Al2O3超细粉的研究

以粗颗粒Al2O3粉为原料,采用气流循环粉碎法制备了d50＜1μm的Al2O3超细粉.按正交表L9(34)安排正交试验,通过方差分析确定了制备Al2O3超细粉的最佳气流循环粉碎条件,并分析了各因素对气流循环粉碎过程的影响程度.不同物料的最佳气流循环粉碎条件应通过实验确定.在本研究的实验条件下,制备Al2O3超细粉的最佳条件为进气压力1.0 MPa,给料压力0.4 MPa,循环时间1.5 h.     

冷却条件对超级钢焊接接头组织和性能的影响

400MPa级超级钢主要特征是高洁净度和超细晶粒组织。采用钨极氩弧焊对400MPa级超级钢施焊,并对其空冷和水冷两种冷却方式下的显微组织和力学性能进行分析。结果表明,空冷条件下焊接接头热影响区（HAZ）晶粒严重长大、强度下降,并出现软化区;焊接过程采用喷水冷却加快了冷却速度,有效抑制了焊接接头热影响区晶粒的长大,改善了接头组织,提高了贝氏体和低碳马氏体的含量,进而改善了接头的综合力学性能,满足实际焊接要求。     

X80管线钢焊接二次热循环粗晶区的韧性和显微组织研究

利用热模拟技术，采用光学、透射电镜和冲击韧度、裂纹尖端张开位移（CTOD）试验研究了X80管线钢在（多道焊接）二次热循环过程中粗晶区的韧性与显微组织的关系。结果表明：当二次峰值温度处于（α＋γ）两相区温度范围时，再热粗晶区的韧性最低，具有明显的临界粗晶区局部脆化倾向，引起临界粗晶区局部脆化的主要原因是形成了粗大的岛状组织。     

Mechanical Properties of Submicrometer‐Grained Transparent Yttria Ceramics by Hot Pressing with Hot‐Isostatic Pressing

Here, we report the fabrication and mechanical properties of submicrometer‐grained (0.29–0.58 μm) transparent yttria ceramics by hot pressing combined with hot‐isostatic pressing. The effects of the grain size on the microhardness and the fracture toughness were studied. An unusual decrease of the fracture toughness with an increase in the grain size was revealed, which may be attributed to the different grain size dependence of the fracture behavior of the ZrO₂‐doped yttria ceramics compared to that of other yttria ceramics. The microhardness and fracture toughness of the transparent yttria ceramics were found to be better than those of the large‐grained yttria ceramics.     

圆形超细金属／合金丝研究进展及其在Z箍缩研究中的应用

介绍了圆形超细金属／合金丝制备技术基本原理、技术特点及基本性能，主要包括拉拔技术、电解腐蚀技术及熔融快速凝固技术。回顾了超细W、Mo、Al丝等在Z箍缩丝阵负载材料中的应用。     

The formation of PSB-like shear bands in cyclically deformed ultrafine grained copper processed by ECAP

Cyclic deformation was performed on ultrafine grained copper processed by ECAP. Shear bands (SBs) and adjacent microstructures were investigated using electron channeling contrast in scanning electron microscope. The possible formation mechanism of SB was discussed based on the characteristic distribution of defects introduced by ECAP.     

粗粒含量对砾质土工程性质影响的研究

 在重型击实或碾压后，砾质土的工程性质主要受粗粒含量的不同而变化。本文结合水布垭高心墙堆石坝防渗材料的研究，分析了粗粒含量对砾质土压实性、渗透性、压缩性、应力应变关系参数的影响。研究表明：砾质土压实性和渗透性除与粗粒含量有关外，还与细料特性有关；相同压实条件下，强度参数与P5关系密切。     

细粒级掺杂石墨材料的制备及其出气特性的研究

通过球磨分散方法制备了细粒级掺杂石墨 ,采用SEM、EDX、TEM、XRD等手段分析了材料微观结构 ,并对其性能作了初步研究。研究表明 :当原始粉粒径小于 10 0nm时 ,材料具有高的热导率和优良的物理机械性能 (抗弯强度为 116MPa) ,与粗晶石墨材料相比 ,细晶石墨材料在电子束辐照前的出气性能与其基本相同。而辐照之后 ,细晶石墨材料释放的H2 、H2 O、CO ,特别是CO2 的量远远少于粗晶石墨材料释放的量     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.